RPC weekly meeting

Wednesday 7 Feb 2024, 13:00 → 16:00 Europe/Bucharest

Conference Room

Mariana Petris (National Institute for R&D in Physics and Nuclear Engineering (IFIN-HH), Bucharest)

13:00 → 13:10 Status of the connector PCBs

• connector soldering status
• gluing the PCBs on the back panel

Speakers: Daniel Bartos, George Stoian, Valerica Aprodu, Viorel Duta

13:10 → 13:20 Status of the twisted pair signal cable for implementation in M0

• cutter procurement

Speakers: George Stoian, Gheorghe Caragheorgheopol, Valerica Aprodu

13:20 → 13:40 Manufacture of the gas distributors for chambers and back panel

Speaker: Laura Radulescu (IFIN-HH)

Buna Andrei,

Asa cum am discutat acum cateva saptamani, vom avea nevoie sa incepem printarea distribuitoarelor de gaz pentru cutia modulului M0, pentru care ne-ai realizat deja mostrele finale (desene stl atasate). Pentru cel de tip mic (6 stuturi) numarul de bucati este 12, iar pentru cel de tip mijlociu (10 stuturi) 8 bucati. Daca sunt neclaritati, in orice privinta, vorbim.

Multumesc!

Cu bine,
Laura

13:40 → 13:50 Status of the implementation of the the gas distributors on the back panel of M0

Speakers: Andrei Radu, Laura Radulescu (IFIN-HH)

Distribuitoare in modulul M0

• se vor realiza desenele de executie pentru noile variante de distribuitoare (mici modificari fata de varianta printata deja) - Radu Andrei
• se va realiza modelul 3D si se vor da la printat - Laura Radulescu

Distribuitoare pentru detectorii RPC 

• printarea unei perechi input/output pentru fiecare tip: MRPC1a (56 mm strip), MRPC1b(96 mm strip), MRPC1c(196 mm strip) 

 

 

 

 

 

 

13:50 → 14:00 M0 back panel equipment

• connectors
• gas distributors
• gas connectors
• HV connectors
• sealing gasket

Speakers: Andrei Radu, George Stoian, Valerica Aprodu, Viorel Duta

14:00 → 14:20 Design of the CBM-TOF inner zone based on the direct flow MSMGRPCs

gas distributors implementation in M1, M2 and M3 modules - discussions

Speakers: Andrei Radu, Laura Radulescu (IFIN-HH), Viorel Duta

14:20 → 14:40 INVENTOR compatibility check and procurement

Speakers: Laura Radulescu (IFIN-HH), Viorel Duta

14:40 → 15:00 backup of the all files belonging to the design of the CBM-TOF inner zone

All people involved have to create a folder on her/his computer where to save the files already approved to be sent for manufacture. A back up of these folders will be made on an external hard disk.

Speaker: Mariana Petris (National Institute for R&D in Physics and Nuclear Engineering (IFIN-HH), Bucharest)

15:00 → 15:20 Assembling manual

Speakers: Mariana Petris (National Institute for R&D in Physics and Nuclear Engineering (IFIN-HH), Bucharest), Valerica Aprodu

15:20 → 15:30 Status of the in-kind contract draft

Speakers: Mariana Petris (National Institute for R&D in Physics and Nuclear Engineering (IFIN-HH), Bucharest), Prof. Mihai Petrovici (National Institute for Physics and Nuclear Engineering (IFIN-HH))

CBM-TOF_Inner_Wall_Costs.pdf